【HAL】stm32F103 DAC+DMA+TIM6查表法产生正弦波-526互联

一、平台
在这里插入图片描述
二、配置
1、DAC的配置

输出缓冲Output Buffer建议关闭。DAC的输出缓存可以用来减小输出阻抗，无需外部运放即可直接驱动外部负载。但输出不能达到0（会出现底部失真），不推荐开启。具体参考官方手册，缓冲器打开时低端的DAC输出电压大概0.2V（不同型号可能不同，暂未考证）
在这里插入图片描述
2、DMA的配置

DMA的工作模式：Circular

3、TIM6的配置
在这里插入图片描述

定时器的配置决定了输出的正弦波的频率。

定时器时钟设为72M。
正弦波的频率=主频 /（TIM_Prescaler+1）/（TIM_Period+1）/ 点数
选100个点
f=72M/(5+1)/(5+1)/100=20kHz.

三、生成代码
需要添加的：
在mian.c中定义查表的数组，保存于静态内存。

const uint16_t Sine12bit[100]={
0x0800,0x0881,0x0901,0x0980,0x09FD,0x0A79,0x0AF2,0x0B68,0x0BDA,0x0C49,
0x0CB3,0x0D19,0x0D79,0x0DD4,0x0E29,0x0E78,0x0EC0,0x0F02,0x0F3C,0x0F6F,
0x0F9B,0x0FBF,0x0FDB,0x0FEF,0x0FFB,0x0FFF,0x0FFB,0x0FEF,0x0FDB,0x0FBF,
0x0F9B,0x0F6F,0x0F3C,0x0F02,0x0EC0,0x0E78,0x0E29,0x0DD4,0x0D79,0x0D19,
0x0CB3,0x0C49,0x0BDA,0x0B68,0x0AF2,0x0A79,0x09FD,0x0980,0x0901,0x0881,
0x0800,0x077F,0x06FF,0x0680,0x0603,0x0587,0x050E,0x0498,0x0426,0x03B7,
0x034D,0x02E7,0x0287,0x022C,0x01D7,0x0188,0x0140,0x00FE,0x00C4,0x0091,
0x0065,0x0041,0x0025,0x0011,0x0005,0x0001,0x0005,0x0011,0x0025,0x0041,
0x0065,0x0091,0x00C4,0x00FE,0x0140,0x0188,0x01D7,0x022C,0x0287,0x02E7,
0x034D,0x03B7,0x0426,0x0498,0x050E,0x0587,0x0603,0x0680,0x06FF,0x077F,
};
uint16_t DualSine12bit[100];
1
2
3
4
5
6
7
8
9
10
11
12
13

在main函数中读取数组并输出

int main(void)
{
  /* USER CODE BEGIN 1 */
  uint32_t Idx;        //定义变量
  /* USER CODE END 1 */
/* MCU Configuration--------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */

HAL_Init();
/* USER CODE BEGIN Init */
/* USER CODE END Init */
/* Configure the system clock */

SystemClock_Config();
/* USER CODE BEGIN SysInit */
/* USER CODE END SysInit */
/* Initialize all configured peripherals /

MX_GPIO_Init();

MX_DMA_Init();

MX_DAC_Init();

MX_TIM6_Init();

/ USER CODE BEGIN 2 /

/读入正弦波数据*/

for (Idx = 0; Idx <100; Idx++)

{

DualSine12bit[Idx] = (Sine12bit[Idx] << 16)+ (Sine12bit[Idx]);

}

HAL_TIM_Base_Start(&htim6);

HAL_DAC_Start_DMA(&hdac,DAC_CHANNEL_1,(uint32_t )DualSine12bit,100,DAC_ALIGN_12B_R);

/ USER CODE END 2 */
/* Infinite loop /

/ USER CODE BEGIN WHILE /

while (1)

{

/ USER CODE END WHILE */
/* USER CODE BEGIN 3 */

}

/* USER CODE END 3 */

}
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48